Hardware Installation Requirements

You must have the following items before installing the MegaRAID Enterprise

MAN 471 QH 1600 PCI RAID controller in a server

5 30 00 Enterprise 1600 64 bit Ultra 160M RAID controller with cache memory

Host computer with an available 64 bit PCI expansion slot it will also

work in a 32 bit slot and non 160M drives

Enterprise 1600 installation CD

Necessary SCSI cables and terminators

An Uninterruptible Power Supply UPS for the entire system is

MegaRAID Enterprise 1600

recommended

160 m SCSI hard disk drives and other SCSI devices as desired

Optional SCSI cables that interconnect the Enterprise 1600 to

64 Bit 66 MHz PCI RAID Controller With Four external SCSI devices

Ultra 160M SCSI Channels Offset connectors are needed for external connectors if stacked

Installation Steps

If you need only the basic MegaRAID features and your computer does not use

other adapter cards with resource settings that may conflict with the MegaRAID

Enterprise 1600 settings the following steps will make your installation quick

and easy For all other configurations please refer to the hardware manual

Check Step Action

u 1 Unpack the controller and inspect for damage

u 2 Turn the computer off and remove the cover

u 3 Make sure the motherboard jumper settings are correct

u 4 Install cache memory on the MegaRAID Enterprise 1600

controller A minimum of 8 MB of cache is required

u 5 Check the jumper settings on the MegaRAID Enterprise

1600 controller See Step 5 in the hardware installation

manual for more details

u 6 Set SCSI termination

u 7 Set SCSI terminator power TermPWR

u 8 Connect the Battery Harness optional

u 9 Install the MegaRAID Enterprise 1600 card

u 10 Connect the SCSI cables to the SCSI devices

u 11 Set target IDs for the SCSI devices

u 12 Replace the computer cover and turn the power on

Thank you for purchasing the MegaRAID Enterprise 1600 PCI RAID controller Please u 13 Run MegaRAID Enterprise 1600 configuration utility

take a few minutes to review this quick guide before beginning the installation optional

process If you require a further explanation of any item covered in this guide u 14 Install software drivers for the desired operating systems

please refer to the complete hardware manual

Step 1 Unpack

Contents for the MegaRAID Enterprise 1600 Unpack and install the hardware in a static free environment The MegaRAID

You should have received controller card is packed inside an anti static bag between two sponge sheets

MegaRAID Enterprise 1600 RAID controller Remove the controller card and inspect it for damage If the card appears damaged

MegaRAID Driver and Documentation CD which includes or if any items listed in the box to the left are missing contact American

u MegaRAID Enterprise 1600 Drivers and Utilities Megatrends Technical Support at 770 246 8645 The MegaRAID Controller is

u MegaRAID Enterprise 1600 Hardware Guide shipped with the following items on CD

u MegaRAID Configuration Software Guide MegaRAID Configuration Software Operating System and

u MegaRAID Operating Systems Drivers Guide Enterprise 1600 Hardware Guides

Software License Agreement MegaRAID Drivers and Configuration Utilities

Warranty Registration Card Software License Agreement

Warranty registration card

Technical Support

If you need help installing configuring or running the MegaRAID Enterprise

Step 2 Power Down

1600 call American Megatrends Technical Support at 770 246 8645 Before you

Turn off the computer and remove the cover Make sure the computer is discon

call please complete the MegaRAID Problem Report in the hardware manual

nected from any networks before installing the controller card

Web Site http www ami com

Step 3 Configure Motherboard

Make sure the motherboard is configured correctly for MegaRAID MegaRAID is

essentially a SCSI Controller Each MegaRAID card you install will require an available

PCI IRQ make sure an IRQ is available for each controller you install

Step 4 Install Cache Memory

Important A minimum of 8 MB of cache memory is required The cache memory

Universal Operating System Software Drivers must be installed before MegaRAID Enterprise 1600 is operational

All MegaRAID controllers include configuration utilities and drivers for

Novell NetWare 4 x and 5 0 Install cache memory DIMMs on the MegaRAID Enterprise 1600 controller card in

HAM DDFS and ASPI Driver the cache memory socket Use a 64 bit 3 3V single sided or double sided 168 pin

Windows NT 4 0 2000 unbuffered DIMM Lay the controller card component side up on a clean static free

Miniport Driver surface The memory socket is mounted flush with the MegaRAID card so the DIMM

SCO Unix 5 0 is parallel to the MegaRAID card when properly installed The DIMM clicks into

MSCSI Driver place indicating proper seating in the socket The MegaRAID card is shown laying

OS 2 Warp 4 x and E business on a flat surface below

MSCSI Driver

UnixWare SMP 2 x 7 0

PDI Driver

DOS 5 0 and Above

ASPI driver

Linux Redhat

Solarisx86 2 6 7 and 8

Lay the controller card component side up on a clean static free surface and install the DIMMs

NOTE The DOS drivers for the MegaRAID Express are contained in the firmware

The DIMMs click into place indicating proper seating in the socket as shown above

Quick Hardware Installation Guide

Step 5 Set Jumpers Step 11 Set Target IDs

Make sure the jumper settings on the MegaRAID Enterprise 1600 card are correct Set target identifiers TIDs on the SCSI devices Each device in a specific SCSI

Jumper setting details can be found in the Enterprise 1600 Hardware Guide channel must have a unique TID in that channel Non disk devices such as CD ROM

or tape drives should have unique SCSI IDs regardless of the channel to which they

Step 6 Set SCSI Termination are connected

Each MegaRAID SCSI channel can be individually configured for termination enable

mode by setting the J2 J3 J5 and J7 jumpers Step 12 Power Up

Replace the computer cover and reconnect the AC power cords Turn power on to

You must terminate the SCSI bus properly Set termination at both ends of the SCSI the host computer Set up the power supplies so the SCSI devices are powered up

cable The SCSI bus is an electrical transmission line and must be terminated at the same time as or before the host computer If the computer is powered up

properly to minimize reflections and losses Typical configuration is to set the before a SCSI device the device might not be recognized

Termination Enable jumpers to allow software to set termination automatically

During boot the MegaRAID Enterprise 1600 BIOS message appears

Note The default jumper settings on the controller for both Termination and

TermPWR normally do not need to be changed MegaRAID Enterprise 1600 Disk Array Adapter BIOS Version x xx date

Copyright C American Megatrends Inc

Firmware Initializing Scanning SCSI Device etc

Step 7 Set SCSI Terminator Power TermPWR

Important All MegaRAID Enterprise 1600 SCSI channels need TermPWR to operate

The firmware takes several seconds to initialize During this time the adapter will

If a channel is not being used make sure the TermPWR jumper for that channel is

scan each SCSI channel When it is ready the following lines will appear

set to supply TermPWR from the PCI bus Jumpers J9 J10 J11 and J12 control

TermPWR on the Enterprise 1600

host Adapter 1 Firmware Version x xx date DRAM Size 8 MB

0 Logical Drives found on the Host Adapter

Step 8 Connect the Battery Harness Optional 0 Logical Drives handled by BIOS

You can install a battery pack onto the Series 471 MegaRAID Enterprise 1600 160M Press Ctrl M to run MegaRAID Enterprise 1600 BIOS Configuration

RAID controller Call Technical Support at 770 246 8645 for more information Utility

The Ctrl M prompt times out after several seconds

The MegaRAID Enterprise 1600 host adapter controller number firmware version

and cache DRAM size are displayed in the second portion of the BIOS message The

numbering of the controllers follows the PCI slot scanning order used by the host

motherboard

MegaRAID Enterprise 1600 Card Layout

Step 9 Install the MegaRAID 1600 Card Step 13 Run MegaRAID Enterprise 1600 Configuration Utility

The MegaRAID card can plug into a 32 bit or 64 bit PCI slot that receives 5 V and Press Ctrl M or Ctrl H to run the MegaRAID Enterprise 1600 Configuration

optionally 3 3 V through the motherboard Choose a PCI slot and align the Mega Utility A screen such as the one shown below displays See the MegaRAID Configura

RAID controller card bus connector to the slot Press down gently but firmly to make tion Software Guide for information about running MegaRAID Configuration Utility

sure that the card is properly seated in the slot The bottom edge of the controller

card should be flush with the slot Insert the MegaRAID card in a PCI slot as

shown below

Step 10 Connect the SCSI Cables to the SCSI Devices

Connect the SCSI cables to the SCSI devices The MegaRAID Enterprise 1600

controller provides two types of connectors two internal high density 68 pin

SCSI connectors and four external ultra high density 68 pin SCSI connectors

Step 14 Installing Software Drivers for the Desired Operating

Offset connectors are needed for external connectors if stacked

Systems

For driver installation procedures please refer to the MegaRAID Operating Systems

Drivers Guide on the Drivers and Documentation CD

AMI Corporate Headquarters United Kingdom Taiwan

American Megatrends Inc 9th Floor Hayes Gate House Suite A Floor 6 No 150

6145 F Northbelt Parkway 27 Uxbridge Road Tun Hwa N Road

Norcross GA 30071 2976 Hayes Middlesex UB4 OJN U K Taipei Taiwan R O C

Sales 800 828 9264 sales ami com Tel 44 208 848 8686 Fax 44 208 848 8588 Tel 886 2 2716 0036 Fax 886 2 2718 1121

Main 770 246 8600 Fax 770 246 8790

Japan Korea

Germany 2 5 15 Sotokanda K Bld 6F Suite 3F B 773 6 w w w a m i c o m

Carl Zeiss Ring 7a Sotokanda Chiyoda ku Ryucksam Dong Kangnam Ku

85737 Ismaning Germany Tokyo 101 Japan Seoul 135 080 Korea

Tel 49 89 9699 9510 Fax 49 89 9699 9519 Tel 81 3 3526 9708 Fax 81 3 3526 9701 Tel 82 2 569 5689 Fax 82 2 569 4689

2000 American Megatrends Inc All rights reserved Printed in the U S A

MAN 475 QH

5 30 00 Hardware Installation Requirements

You must have the following items before installing the MegaRAID Express

500 PCI RAID controller in a server

Express 500 controller with cache memory

Host computer with an available 3 3v or 5v 32 bit PCI expansion slot

Express 500 installation CD

Necessary SCSI cables and terminators

MegaRAID Express 500 An Uninterruptible Power Supply UPS for the entire system is

recommended

Low Cost Ultra 160M RAID Controller

Installation Steps

If you need only the basic MegaRAID features and your computer does not

use other adapter cards with resource settings that may conflict with the

MegaRAID Express 500 settings the following steps will make your installa

tion quick and easy For all other configurations please refer to the hard

ware manual

Check Step Action

u 1 Unpack the controller and inspect for damage

u 2 Turn the computer off and remove the cover

u 3 Make sure the motherboard jumper settings BIOS

settings are correct

u 4 Install cache memory on the MegaRAID Express 500

controller A minimum of 16 MB of cache is required

u 5 Check the jumper settings on the MegaRAID Express

500 controller See Step 5 in the hardware installation

manual for more details

u 6 Set SCSI termination

u 7 Set SCSI terminator power TermPWR

u 8 Install the MegaRAID Express 500 card

u 9 Connect the SCSI cables to the SCSI devices

u 10 Set target IDs for the SCSI devices

u 11 Replace the computer cover and turn the power on

u 12 Run MegaRAID Express 500 configuration utility

optional

Thank you for purchasing the MegaRAID Express 500 PCI RAID controller u 13 Install operating system and MegaRAID software drivers

Please take a few minutes to review this quick guide before beginning the for the desired operating systems

installation process If you require a further explanation of any item covered in this

guide please refer to the complete hardware manual

Step 1 Unpack

Contents for the MegaRAID Express 500 Unpack and install the hardware in a static free environment The

You should have received MegaRAID Express 500 controller card is packed inside an anti static bag

MegaRAID Express 500 RAID controller between two sponge sheets Remove the controller card and inspect it for

MegaRAID Driver and Documentation CD which includes damage If the card appears damaged call your American Megatrends

u MegaRAID Express 500 Drivers and Utilities Technical Support representative at 770 246 8645

u MegaRAID Express 500 Hardware Guide

u MegaRAID Configuration Software Guide

Step 2 Power Down

u MegaRAID Operating Systems Drivers Guide

Turn off the computer and remove the cover Make sure the computer is

Software License Agreement

disconnected from any networks before installing the controller card

Warranty Registration Card

Technical Support Step 3 Configure Motherboard

If you need help installing configuring or running the MegaRAID Express 500 Make sure the motherboard is configured correctly for MegaRAID Express

PCI RAID Controller call your American Megatrends Technical Support repre 500 MegaRAID Express 500 is essentially a SCSI controller Each MegaRAID

sentative at 770 246 8645 Before you call please complete the MegaRAID Express 500 card you install requires an available PCI IRQ make sure an IRQ

Problem Report form on the next page is available for each controller you install

Step 4 Install Cache Memory

Use 72 bit 3 3V unbuffered SDRAM only The maximum memory bandwidth

is 528 MB sec

For more information on SDRAM specifications refer to the MegaRAID

Express 500 Hardware Guide

Important A minimum of 16 MB of cache memory is required The cache

memory must be installed before MegaRAID Express 500 is operational

Universal Operating System Software Drivers Install cache memory on the MegaRAID Express 500 card in the DIMM

All MegaRAID controllers include configuration utilities and drivers for socket This socket accepts a 168 pin DIMM

Novell NetWare 4 x and 5 0

HAM DDFS and ASPI Driver Lay the controller card component side up on a clean static free surface to

Windows NT 4 0 2000 install the DIMM The memory socket is mounted flush with the MegaRAID

Miniport Driver Express 500 card so the DIMM will stand at a right angle to the MegaRAID

SCO Unix 5 0 card when properly installed The DIMM clicks into place indicating proper

MSCSI Driver seating in the socket as shown below The MegaRAID card is shown laying

OS 2 Warp 4 x and E business on a flat surface in the illustration below

UnixWare SMP 2 x 7 0

PDI Driver

Linux Redhat

Solarisx86 2 6 7 and 8

DOS 5 0 and Above

ASPI driver

NOTE The DOS drivers for the MegaRAID Express are contained in the firmware

except the DOS ASPI and CD ROM drivers

2000 American Megatrends Inc All rights reserved Printed in the U S A

Quick Hardware Installation Guide

Step 5 Set Jumpers Step 11 Power up

Make sure the jumper settings on the MegaRAID Express 500 card are Replace the computer cover and reconnect the AC power cords Turn power

correct Jumper setting details can be found in the MegaRAID Express 500 on to the host computer Set up the power supplies so the SCSI devices are

Hardware Guide powered up at the same time as or before the host computer If the com

puter is powered up before a SCSI device the device might not be recog

Step 6 Set Termination nized

The MegaRAID SCSI channel can be configured for termination enable mode by

setting the J1 Termination Enable jumper During boot the MegaRAID Express 500 BIOS message appears

You must terminate the SCSI bus properly Set termination at both ends MegaRAID Express 500 Disk Array Adapter BIOS Version x xx date

of the SCSI cable The SCSI bus is an electrical transmission line and must be Copyright C American Megatrends Inc

Firmware Initializing Scanning SCSI Device etc

terminated properly to minimize reflections and losses Typical configuration is to

set the Termination Enable jumpers to allow software to set termination automati

The firmware takes several seconds to initialize During this time the adapter

cally

will scan each SCSI channel When it is ready the following lines appear

Note The default jumper settings on the controller for both Termination and

host Adapter 1 Firmware Version x xx date DRAM Size 4MB

TermPWR normally do not need to be changed 0 Logical Drives found on the Host Adapter

0 Logical Drives handled by BIOS

Step 7 Set Terminator Power TermPWR Press Ctrl M to run MeagRAID Express 500 BIOS Configuration

Important Both MegaRAID Express 500 SCSI channels need TermPWR to Utility

operate If a channel is not being used and no auxiliary power source is The Ctrl M prompt times out after several seconds

connected change the jumper setting for that channel to supply TermPWR The MegaRAID Express 500 host adapter controller number firmware

from the PCI bus version and cache DRAM size are displayed in the second portion of the

BIOS message The numbering of the controllers follows the PCI slot scan

ning order used by the host motherboard

MegaRAID Express 500 Card Layout

Step 8 Installing the MegaRAID Express 500 Step 12 Running the MegaRAID Express 500 BIOS Setup

Choose a 3 3 V PCI slot and align the MegaRAID Express 500 controller Press Ctrl M or Ctrl M to run the MegaRAID Express 500 BIOS

card bus connector to the slot Press down gently but firmly to make sure the card is setup utility A screen such as the one below displays See the MegaRAID

properly seated in the slot The bottom edge of the controller card should be flush Configuration Software Guide for information about running MegaRAID 64 LVD

with the slot BIOS setup

Step 9 Installing the MegaRAID Express 500

Connect the SCSI cables to the SCSI devices The MegaRAID Express 500

controller provides two types of connectors one internal high density

68 pin SCSI connector and one external ultra high density 68 pin SCSI

connector

Step 13 Installing Software Drivers for the Desired Operat

ing System

For driver installation procedures please refer to the MegaRAID Operating

System Drivers Guide on the Drivers and Documentation CD

Step 10 Set Target IDs

Set target identifiers TIDs on the SCSI devices Each device in a specific SCSI

channel must have a unique TID in that channel Non disk devices such as CD

ROM or tape drives should have unique SCSI IDs regardless of the channel to

which they are connected

AMI Corporate Headquarters United Kingdom Taiwan

American Megatrends Inc 9th Floor Hayes Gate House Suite A Floor 6 No 150

6145 F Northbelt Parkway 27 Uxbridge Road Tun Hwa N Road

Norcross GA 30071 2976 Hayes Middlesex UB4 OJN U K Taipei Taiwan R O C

Sales 800 828 9264 sales ami com Tel 44 208 848 8686 Fax 44 208 848 8588 Tel 886 2 2716 0036 Fax 886 2 2718 1121

Main 770 246 8600 Fax 770 246 8790

Japan Korea

Germany 2 5 15 Sotokanda K Bld 6F Suite 3F B 773 6 w w w a m i c o m

Carl Zeiss Ring 7a Sotokanda Chiyoda ku Ryucksam Dong Kangnam Ku

85737 Ismaning Germany Tokyo 101 Japan Seoul 135 080 Korea

Tel 49 89 9699 9510 Fax 49 89 9699 9519 Tel 81 3 3526 9708 Fax 81 3 3526 9701 Tel 82 2 569 5689 Fax 82 2 569 4689

2000 American Megatrends Inc All rights reserved

Printed in the U S A

Peace of mind

The Nokia 6086 phone makes communication easy with an ergonomic keypad large display and excellent indoor

coverage with UMA Unlicensed Mobile Access over WLAN networks

Features at a glance Stay connected with family and friends

with longer talk times and improved

audio quality

Fold design with easy to use keypad

and large display Excellent indoor coverage and seamless

multi network use with UMA

Incoming calls are shown on the cover

unlicensed mobile access over WLAN

display no need to open the fold to

see who s calling Up to 2GB expandable memory

Operating Frequency Memory Functions Digital Services

Quad band GSM EDGE coverage on five continents 5 MB free user memory MIDI 64 MP3 AAC AAC and AMR WB ringing

850 900 1800 1900 Expandable memory microSD card up to 2GB tones

WLAN 802 11 b g 2 4 Ghz for UMA with automatic with hot swapping Picture ringing tones

switching between WLAN and cellular networks Plug and play mobile services

Applications Firmware over the air updates

Display Java MIDP 2 0 games and applications Kodak image service upload store share

Main display 1 8 CSTN passive LCD display print your photos

supports up to 262 144 colors 128 x 160 pixels Connectivity Adobe Photoshop Album SE 3 0 PC software

External cover display 1 FSTN black and white Seamless coverage and handover between WLAN

screen with blue LEDs 96 x 68 pixels and cellular services using UMA technology Other Features

Bluetooth version 2 0 with Enhanced Data Rate Flight and demo mode

User Interface includes SIM access and Headset and Handsfree Prepaid tracker

Active standby profiles Themes including Flash themes animated

Keypad 3 user configurable softkeys 4 way scroll Pop Port connector with USB 1 1 connectivity wallpapers and screensavers color schemes and

dedicated volume keys and camera key 12Mbit s ringing tones

Local and remote over the air TA device to

Imaging device data synchronization with SyncML Sales Package Contents

VGA camera with 4 x digital zoom calendar to do list phonebook Nokia 6086 phone

Video recorder and player PC synchronization using Nokia PC Suite with USB Nokia Battery BL 5C

and Bluetooth connectivity Nokia Compact Charger AC 3

Messaging Nokia Headset HS 5

Common inbox for SMS and MMS Browsing User guide and quick guide

MMS 1 2 for creating receiving editing and XHTML browser over TCP IP

sending multimedia messages messages up to Smart content download with MA digital rights Power Management

300 kB management 1 0 Battery BL 5C

Push to talk Talk time Pure GSM up to 5 hours

Email supports SMTP P P3 IMAP4 protocols Data Transfer Talk time UMA up to 6 hours

Instant messaging EDGE EGPRS Class 10 Standby time Pure GSM up to 10 days

Nokia Xpress audio messaging a quick and easy GPRS Class 10 Standby time UMA up to 4 days

way to send a voice or sound clip via MMS Charging 970 mAh

Personal Information Management PIM

Multimedia Calendar to do list notes peration times vary depending on the network and

peration times vary depending on the network and

Music player supporting MP3 MP4 AAC AAC Contacts usage

eAAC WMA formats Expense manager

Advanced Audio Distribution Profile A2DP for Alarm clock countdown timer

stereo audio streaming over Bluetooth technology

FM stereo radio with Visual Radio Voice Features

Streaming video 3GPP Integrated handsfree speaker

Macromedia Flash Player 2 0 Enhanced voice commands dialing SIND

Voice recording

Artificial Bandwidth Expansion ABE

Single Antenna Interface Cancellation SAIC www europe nokia com 6086

Available colors Dimensions

92 mm

46 mm 23 mm

Black Weight 84 g

Volume 84 cc

08 12 2006